CONTINUOUS FURNACE FOR CARBURIZING, HARDENING AND TEMPERING

return to main page of continuous furnaces

return to main page of heat treatment equipment

 

FRONT WASHING TANK

 

RG-800A RG-801 RG-804 RG-805/810A RG-806 RG-807 RG-808/810B RG-809 RG-802A+B RG-810C
Feeder Gas generatior Front washing Quenching furmace Quenching tank Rear washing Tempering furnace Dyeing tank Carbon control Control panel

 

Furnace line for heat treatment of conveyer type

 

DATA AND SPECIFICATIONS OF THE FIRST WASHING DEVICE

 

RG804-1 the first electric heated immersion washing device: wash tank
Degreasing Area                             60…80ºС
Phosphate removal Area                        60…80ºС
Washing zone                                                      60…80ºС
Hot air drying zone                 80…100ºС
For one bath mentioned above, 1 pump and 6 heaters with a total capacity of 78 kW are applied. The heaters are used as spare power sources and only at the beginning of the furnace application (see. Note below);
Note:
The heat source of the sink is the heat arised from hardening furnace gas burners and its heating system (heating temperature of the water is up to 80 ° C). Design and construction of piping performs by the Buyer according to the scheme provided by the Seller. You also need additional heat exchanger. Heaters in the sink are usually switched off and work only when you start the oven.The washing machine 6 heaters are also installed, 13 kW each
 
Irrigation system for degreasing, washing phosphate removal zones (one system);
Pumps for irrigation                                                        1 pcs
Oil separator operates on the principle of densities separation 1 pcs
Electric heating (13 kW)                                                        6 pcs
The volume of washing tank                                   about 2,7 m3
Engine power                                                   0,75 kW
The volume of containers for degreasing                                   about  3 m3
The volume of containers for phosphate removal                                   about  3 m3
The volume of containers for washing                                    about  3 m3

 

Front /back electrically heated immersion washing machine


Model
Conveyor width, mm Supporting power, kw Tank capacity, l Pumps for circulation and degreasing, HP, л.с  External dimensions of the tank, mm
Width Height Length
RG-804(807)-A 600 20 1660 (1050) 2 1710 (1390) 2345 (1840) 3430 (3000)
RG-804(807)-1 600 20 1660 (1050) 2 1710 (1390) 2345 (1840) 3430 (3000)
RG-804(807)-2 700 20 1990 (1100) 2 1910 (1490) 2345 (1840) 3430 (3000)
RG-804(807)-3 800 20 2160 (1150) 2 2010 (1590) 2345 (1840) 3430 (3000)
RG-804(807)-4 1000 20 2500 (1350) 2 2220 (1790) 2345 (1840) 3430 (3000)
RG-804(807)-5 1000 20 2500 (1350) 2 2220 (1790) 2345 (1840) 3430 (3000)
RG-804(807)-6 1000 20 2500 (1350) 3 2220 (1790) 2345 (1840) 3430 (3000)
RG-804(807)-7A 1200 30 2720 (1500) 3 2420 (1990) 2345 (1840) 3430 (3000)
RG-804(807)-7 1400 30 3270 (1800) 5 2690 (2190) 2345 (1840) 3430 (3600)
RG-804(807)-8 1400 30 3270 (1800) 5 2690 (2190) 2345 (1840) 3430 (3600)