WIRE/ROD CALIBRATION EQUIPMENT AND LINES

MAIN PAGE

 

CALIBRATION EQUIPMENT

AUTOMATIC WELDING MACHINE

Automatic welding machine of horizontal type is fully functional welding equipment, widely used in the production of automobile parts, industrial machine parts and electrical parts. The use of this equipment can reduce the cost, increase product quality and performance.

1

Features of welding equipment:

  • Equipped with a control device, providing reliable welding.
  • It supports multiple stationary welding jigs.
  • Rotating device can be attached to side clamps.
  • Compatible with any type of cutting device.

 

Welding equipment specifications

Model THU-15 THU-25 THU-35 THU-45 THU-60 THU-80
Welding Diameter of the rod 3-5 6-25 6-35 8-45 10-60 19-80
Gas tube assembly 17.3 34 48.6 60.5 76.3 101.6
Material length (turning side) Ø15x200 Ø25x300 Ø35x300 Ø42x300 Ø56x300 Ø76x300
Working length after installation 500 650 800 800 800 1200
Power Friction heating kg. 1200 3000 5000 10000 15000 30000
Heading pressure kg. 1300 5000 10000 20000 30000 60000
Main shaft 50 HZ, rev./Min. 4000 2175 2175 2100 1500 800
Welding 60 Hz, rev./Min. 4900 2625 2625 2100 1500 800
The primary turning shaft Switching system, kg = m Electromagnetic multi-plate clutch
40 40 40 70 100 160
Braking time, sec. 0.2 0.2 0.2 0.3 0.3 0.3
Switching system, kg = m Electromagnetic multi-plate clutch
70 70 70 100 160 160
Braking time, sec. 0.2 0.2 0.2 0.3 0.3 0.3
Main bearing shaft length 100 102 110 120 160 180
Forward Speed 6000 5000 5500 5300 5500 3800
Slide Reverse Speed 10000 5300 5500 5500 5500 3700
Moving Range 250 280 280 350 330 300
Chuck Hydraulic collet - - Hydraulic three-throw chuck
Material Processing Chuck Options 2800 6000 9500 9500 12000 15000
Clamp Hydraulic horizontal open system
Length 2100 4500 9000 9900 13000 15800
Adjustment Adjustment Time 0~999.9 0~999.9 0~999.9 0~999.9 0~999.9 0~999.9
Main drive shaft 7.5 7.5 11 15 22 45
Engine Hydraulic 2.2 3.7 3.7 5.5 7.5 11

 

 

CALIBRATION EQUIPMENT

TURNING MACHINES FOR STEEL SURFACE TREATMENT

TURNING MACHINES FOR STEEL SURFACE TREATMENT

Main characteristics:

  • Turning machines for steel surface treatment are widely used for cleaning oxidized, rusty and uneven surfaces of round steel through hot rolling to obtain a bright surface and precise dimensions.
  • Measurement parameters and wear compensation: optical devices control processing, compensate tool wear after the stripping process.
  • Safety: a lubricant and coolant ensure smooth and safe operation of the system.
  • Waste-free production: the principle of operation of the equipment is based on the automatic sorting of waste for recycling.
  • Control system for cleaning the entire production line.
  • Effective workflow monitoring.
  • Equipment of vibration suppression system.
  • Stability of raw material supply.
  • Protection of raw materials from damage.

 

The customer can use the equipment in conjunction with two-roll mill leveler as of autonomous action or in conjunction with continuous production line.

 

CALIBRATION EQUIPMENT

BLAST CLEANING EQUIPMENT

1

The principle of operation of blasting machine is based on centrifugal force of steel drilling shot high-speed rotation in the cylinder. Removal of rust and oxidation film occurs as a result of contact and friction of drilling shot and the surface of the product at high speed. Such a process can be used instead of products chemical etching.

 

CALIBRATION EQUIPMENT

HYDRAULIC CUTTING AND BENDING TOOLS

 

1